Home › Refrigerator Water Filters › Whirlpool › KSRF25FRBT01
Water Filter for the KitchenAid KSRF25FRBT01 (EDR3RXD1)
✓ 100% compatible — no bypass plug needed
🔧 5-min push-in swap
🇺🇸 Ships from Indiana
Every cartridge that fits this model — pulled live from the catalogue:
✓
KSRF25FRBT01 specifics — where the filter actually lives
On the KSRF25FRBT01, the cartridge in the lower fresh-food zone in most side-by-side layouts, knee height or below — usually a kneeling-height or shoulder-height swap, not a teardown. It is a twist-lock bay: no tools, no housing removal, and the cartridge indexes in only one orientation despite looking symmetric.
Before you click buy, two things: the change light ignores the new cartridge until you reset it, and the first removal always takes more muscle than the manual implies. One prefix, one chassis family: it usually marks a side-by-side chassis layout, which means shared cartridge economics — one media family, dozens of cabinet variants, all drinking from the same parts line. The -01 tail tracks the revision ladder — each rung shares the identical EDR3RXD1 bay.
KSR vs KTR — what the prefix tells you
The KSR/KTR pair divides this family by layout — KSR means side-by-side chassis, KTR means top-freezer. For filter shopping the distinction matters less than you would think — same line, different cabinet. Working from the model code, the KSRF25FRBT01 lands somewhere around 2005 to 2009; treat the window as approximate.
Swap it in 5 minutes
- Twist the old cartridge a quarter turn counterclockwise and pull it straight down — keep a towel in reach for the dribble.
- Fill the new cartridge with cold tap water so the chamber is not fighting an air pocket.
- Offer the new cartridge to the bay, push up, and twist a quarter turn clockwise until the stop catches.
- Run two gallons through the dispenser to flush carbon fines, then hold the filter-reset control until the status light clears.
What this filter takes out of your water
| What it targets | Standard that covers it |
|---|---|
| Chlorine taste & odor | NSF/ANSI 42 — aesthetic effects |
| Particulates, Class I | NSF/ANSI 42 — fine sediment |
| Lead | NSF/ANSI 53 — health effects |
| Cysts (cryptosporidium, giardia) | NSF/ANSI 53 — microbial |
| PFOA & PFOS | NSF/ANSI 53 (P473) — varies by cartridge |
Coverage above lists what the standard addresses, not a performance claim for any specific cartridge — removal claims vary by certificate, so check the NSF listing for the exact part number you are buying.
KSRF25FRBT01 filter questions
KitchenAid KSRF25FRBT01: how do I clear the change-filter light?
Hold the filter-reset control a few seconds after the swap; the status light clears only with a seated cartridge, and the KSRF25FRBT01 manual maps the control by panel type.
Does the KitchenAid KSRF25FRBT01 need a bypass plug when the filter is out?
You can, but unfiltered — the EDR3RXD1 bay needs no bypass plug; it just passes water through without filtering while the cartridge is out.
Are off-brand filters safe for a KitchenAid refrigerator?
Certified aftermarket cartridges are built to the same NSF test standards as the OEM part, and federal warranty law (Magnuson-Moss) protects your coverage when you use them.
Why is the OEM EDR3RXD1 cartridge so much more expensive?
Part of the OEM price is the badge and the distribution chain. Certified alternatives meet the same test standards at a lower unit price, especially in multi-packs.
How often should I replace the filter in my KSRF25FRBT01?
Every six months or at the rated gallon capacity, whichever comes first — the EDR3RXD1 class cartridges all share that service interval.
Do I need to turn off the water supply to change it?
No — the bay is designed for a live swap. Expect a small dribble, keep a towel in reach, and flush a couple of gallons through the new cartridge before the first glass.
Every filter that fits your fridge
| Cartridge | OEM EDR3RXD1 | RECOMMENDEDEDR3RXD1 Replacement Water Filter · 1-Pack – ClearFit | EDR3RXD1 Replacement Water Filter · 3-Pack – ClearFit | EDR3RXD1 Replacement Water Filter · 6-Pack – ClearFit |
|---|---|---|---|---|
| Price | OEM list | $17.99 | $44.97 | $80.94 |
| Verified fit | ✓ the bay cartridge | View & buy → | View & buy → | View & buy → |
This filter expires six months from today
Your HVAC filter is probably on a different cycle. Track them all in one place.
months until this filter should be replaced (200-gal rated life)
Free tool · tracks fridge + HVAC + whole-house · auto-refill optional
More models using this filter
Related guides
POPULAR GUIDE
How to change a Whirlpool refrigerator water filter
Every Filter 1–6 bay location — including the door-mounted bays on WRX models, with door-open angles and cap-release quirks. — read the guide →
POPULAR GUIDE
How to reset your Whirlpool filter light
Filter 1–6 indicator maps showing which key actually clears the light on your panel. — read the guide →
WATER PROBLEM GUIDE
Does your fridge filter remove fluoride?
What EDR1RXD1-class carbon blocks actually take out — and the systems that do remove fluoride. — read the guide →