Home › Refrigerator Water Filters › Whirlpool › KSBS25INBT01
Water Filter for the KitchenAid KSBS25INBT01 (EDR3RXD1)
✓ 100% compatible — no bypass plug needed
🔧 5-min push-in swap
🇺🇸 Ships from Indiana
Every cartridge that fits this model — pulled live from the catalogue:
✓
KSBS25INBT01 specifics — where the filter actually lives
The KSBS25INBT01 carries its water filter in the lower fresh-food zone in most side-by-side layouts, knee height or below — usually a kneeling-height or shoulder-height swap, not a teardown. Mechanically the KSBS25INBT01 uses a twist-in cartridge: the ears on the cartridge neck are the guide — line them up, lift into the seat, and quarter-turn home.
Order-day practicalities: the reset control is the step everyone skips; the light will not acknowledge a new cartridge on its own. The KSB in KSBS25INBT01 is doing real work: in this catalog KSB is the side-by-side variant marker; internal layouts vary, the bay layout does not. The two-digit 01 tail is revision bookkeeping. Badge position and shelf trim moved around; the bay geometry did not.
KSB vs KSR — what the prefix tells you
Two prefixes, two missions: Chassis first: side-by-side variant (KSB) versus side-by-side chassis (KSR). The shared cartridge line covers both without adaptation. Whatever the badge on the door says, the parts reality is the EDR3RXD1 media line; that is the anchor every compatible listing hangs from.
Swap it in 5 minutes
- Twist the old cartridge a quarter turn counterclockwise and pull it straight down — keep a towel in reach for the dribble.
- Fill the new cartridge with cold tap water so the chamber is not fighting an air pocket.
- Offer the new cartridge to the bay, push up, and twist a quarter turn clockwise until the stop catches.
- Run two gallons through the dispenser to flush carbon fines, then hold the filter-reset control until the status light clears.
What this filter takes out of your water
| What it targets | Standard that covers it |
|---|---|
| Chlorine taste & odor | NSF/ANSI 42 — aesthetic effects |
| Particulates, Class I | NSF/ANSI 42 — fine sediment |
| Lead | NSF/ANSI 53 — health effects |
| Cysts (cryptosporidium, giardia) | NSF/ANSI 53 — microbial |
| PFOA & PFOS | NSF/ANSI 53 (P473) — varies by cartridge |
Coverage above lists what the standard addresses, not a performance claim for any specific cartridge — removal claims vary by certificate, so check the NSF listing for the exact part number you are buying.
KSBS25INBT01 filter questions
KSBS25INBT01 filter light will not turn off — what is the reset step?
Seat the new cartridge first, then hold the filter-reset control for a few seconds until the status light clears — the exact button placement varies by control panel, so check the KSBS25INBT01 owner’s manual page for filter status.
Running the KSBS25INBT01 with an empty filter bay — does it need a cap?
The bay self-seals: with no cartridge the KSBS25INBT01 still dispenses, just unfiltered. No bypass plug exists for this line.
Are off-brand filters safe for a KitchenAid refrigerator?
Certified aftermarket cartridges are built to the same NSF test standards as the OEM part, and federal warranty law (Magnuson-Moss) protects your coverage when you use them.
Why is the OEM EDR3RXD1 cartridge so much more expensive?
Part of the OEM price is the badge and the distribution chain. Certified alternatives meet the same test standards at a lower unit price, especially in multi-packs.
How often should I replace the filter in my KSBS25INBT01?
Every six months or at the rated gallon capacity, whichever comes first — the EDR3RXD1 class cartridges all share that service interval.
Do I need to turn off the water supply to change it?
No — the bay is designed for a live swap. Expect a small dribble, keep a towel in reach, and flush a couple of gallons through the new cartridge before the first glass.
Every filter that fits your fridge
| Cartridge | OEM EDR3RXD1 | RECOMMENDEDEDR3RXD1 Replacement Water Filter · 1-Pack – ClearFit | EDR3RXD1 Replacement Water Filter · 3-Pack – ClearFit | EDR3RXD1 Replacement Water Filter · 6-Pack – ClearFit |
|---|---|---|---|---|
| Price | OEM list | $17.99 | $44.97 | $80.94 |
| Verified fit | ✓ the bay cartridge | View & buy → | View & buy → | View & buy → |
This filter expires six months from today
Your HVAC filter is probably on a different cycle. Track them all in one place.
months until this filter should be replaced (200-gal rated life)
Free tool · tracks fridge + HVAC + whole-house · auto-refill optional
More models using this filter
Related guides
POPULAR GUIDE
How to change a Whirlpool refrigerator water filter
Every Filter 1–6 bay location — including the door-mounted bays on WRX models, with door-open angles and cap-release quirks. — read the guide →
POPULAR GUIDE
How to reset your Whirlpool filter light
Filter 1–6 indicator maps showing which key actually clears the light on your panel. — read the guide →
WATER PROBLEM GUIDE
Does your fridge filter remove fluoride?
What EDR1RXD1-class carbon blocks actually take out — and the systems that do remove fluoride. — read the guide →